On Tuesday, 17 November, we are closed due to a public holiday. Orders will be shipped on 18 November. Thank you for your understanding.

BetaFPV Matrix 1S AIO P1 HD 12A (FC+ESC+ELRS+VTX)

In Stock
€ 99,89

BetaFPV Matrix 1S AIO P1 HD is an AIO board combining a flight controller, 12A ESCs, an ELRS receiver and a P1 Air Unit digital video transmitter. The board is suitable for Tinywhoops in 65 and 75mm sizes powered by a 1S LiPo battery. It weighs only 4,6g, making a digital whoop only slightly heavier than an analogue one. The Air65 II Champion with this board weighs 17,4g, which is 0,8g more than its analogue version. The board is designed for use with ArtLynk digital video transmission and therefore has no chip for analogue OSD.

ArtLynk is an open digital video transmission system based on Artosyn chips, used by multiple manufacturers. The board works with all devices using the ArtLynk protocol, such as BetaFPV VR04 HD goggles, P1 HD VRX receivers (Standard and Nano), the BetaFPV monitor or XJRC goggles. It is not compatible with other digital systems (DJI, Walksnail, HDZero).

The flight controller is based on an STM32G473 processor clocked at 168MHz combined with a BMI270 gyro. The board features 16MB blackbox memory, a voltage sensor and a BEC 5V/3A. UART3 is used by the receiver and UART4 by the video transmitter, while a full-featured UART2 remains available with pads for connecting an external CRSF/SBUS receiver, GPS or another serial device. LED and buzzer pads are also included. Betaflight OSD is transmitted digitally to the goggles via the video transmitter.

The integrated serial ELRS receiver at 2,4GHz is connected via UART3 and communicates with the flight controller using the CRSF protocol. It is a full-featured receiver with ESP8685 and SX1281 chips, whose firmware can be updated separately via WiFi or through Betaflight passthrough in ExpressLRS Configurator. The receiver antenna is a 31mm long copper wire. ExpressLRS is an advanced open-source RC system with long range, low latency and a high refresh rate.

The ESCs use Bluejay firmware for BB51 hardware with DShot300/600 and bidirectional DShot support, allowing the RPM filter to be used in Betaflight. The default PWM frequency is 96kHz and can also be switched to 24 or 48kHz. The ESCs handle a continuous current of 12A and are therefore suitable for 0702, 0802 and 1102 motors. The board includes a current sensor. Motors connect without soldering via gold-plated JST1.25 connectors.

Video transmission is handled by the integrated P1 Air Unit video transmitter in the 5,1-5,9GHz band with 200mW output power. The live feed has 1080p/60fps resolution and approximately 60ms latency. The package includes an Air HD Camera (1/2,9" sensor, 153° FOV, 16:9 aspect ratio), which connects to the board with a lightweight 15-pin coaxial cable via a DF36-15 connector. Both the camera and cable are also available as spare parts. The video transmitter antenna connects via a u.FL connector. The video transmitter comes with v2.1.2 firmware installed from the factory; BetaFPV goggles and receivers need to be updated to v2.1.3 for compatibility. Latency is higher than with DJI or Walksnail, so we recommend this system more for relaxed flying and exploration than for racing and aggressive freestyle in tight indoor spaces.

The video transmitter gets noticeably hot on the ground, so we do not recommend leaving the whoop powered on for long without flying. Do not power on the board without the video transmitter antenna connected.

The mounting hole spacing is 25,5x25,5mm, board dimensions are 30,5x30,5mm (1mm PCB thickness), and weight is 4,6g without antenna and camera, or 5,99g with the Air HD camera. The battery connects via a BT2.0 connector. To save weight, an external USB-C port connected via an SH1.0 connector is used.

Important warning: Only firmware for the BETAFPV 2.4G AIO V2 RX target may be flashed to the receiver. Do not repeatedly flash the ESC firmware at short intervals, as the board may freeze and burn out.

Firmware

Key Features

  • Input voltage: 1S LiPo
  • MCU: STM32G473CEU6 (168MHz)
  • Gyro: BMI270 (3,2kHz)
  • Barometer: No
  • Blackbox: 16MB
  • OSD: No (no analogue OSD chip)
  • Number of UARTs: 3 (UART2 free, UART3 receiver, UART4 video transmitter)
  • BEC: 5V/3A
  • RC receiver: Integrated serial ELRS 2,4GHz (UART3, CRSF)
  • Antenna connector: No (31mm wire antenna)
  • VTX power: 200mW
  • VTX protocol: ArtLynk (P1 Air Unit)
  • VTX firmware: v2.1.2
  • VTX frequency: 5,1-5,9GHz
  • Resolution and latency: 1080p/60fps, approx. 60ms
  • Camera: Air HD Camera (1/2,9", FOV 153°, 16:9)
  • Camera connector: DF36-15 (15-pin coaxial cable)
  • VTX antenna connector: u.FL
  • Firmware target: BETAFPVG473_V3 (Betaflight 2026.6.1)
  • ESC firmware: Bluejay A_X_5_96KHz_V0.19 (BB51)
  • Continuous current: 12A
  • Input protocol: DShot300, DShot600, bidirectional DShot
  • Current sensor: Yes
  • Motor connector: JST1.25 (gold-plated)
  • Power connector: BT2.0
  • USB connector: External USB-C (SH1.0 4-pin)
  • Mounting holes: 25,5x25,5mm
  • Size: 30,5x30,5mm
  • Weight: 4,6g (without antenna and camera), 5,99g with camera

Package Includes

  • 1x AIO board
  • 1x Air HD Camera with coaxial cable
  • 1x External USB-C connector
  • 1x SH1.0 4-pin connection cable
  • 1x 5,8GHz VTX antenna
  • 4x M1,2x4 self-tapping screw
  • 4x M1,4x5 self-tapping screw
  • 4x Soft mount (1,2mm damping ball)
  • 1x Manual